A Year With a Harbor Freight Table Saw Blade

Every Woodworker goes through the phase of purchasing tools from Harbor Freight (HF).  All of our woodworking magazines come with coupons with prices ridiculously low.  So low most of us warrant its worth the shot for that new _____ we’ve been saving up for.  Instead of paying $500 we can pay $200 with our handy dandy coupon.  We then realize the truth as our $2.00 Clamps break during a crucial glue up, or our $12 electric drill is impossible to control and starts smoking (yeah, true story).  Then we get over it and head back to Sears.

Now to be fair, there are a few gems at HB.  I did construction work during summers in High School and drove a lot of nails, Estwig hammers are great but my premium hammer was lost over the years.  I’ll be honest I love my $5.00 Hammer from HF, it is wonderful. Sure I don’t use it everyday, like before, but I still enjoy using it.  Likewise, their tape measures aren’t as good as your metal bodied Stanley but when you can get them for free with a coupon, you can put one everywhere. My church has a little 3 gallon “hotdog” air compressor that we use for lots of things (for $40 I might get one for the house), but we’ve also got a 20 gallon HF aircomp that is ‘piss-poor’ compared to my Craftsman 10 gallon.

This brings me to the main point; the HF blade I’ve been using for the last year in my Craftsman 10″ table saw.  I got this saw as the closeout of the display model, so I paid $100 for a $300 saw.  It didn’t come with a blade so I bought a general purpose Dewalt blade.  After about a year of use (mostly weekends for a few hours) the blade needed replacing.  I didn’t have a lot of descretionary income for the woodshop but I had a 20% off coupon the good ol’ Harbor Freight.

I bought a 40 Tooth Combination Blade for $12.99. It has been a good blade and is still going strong. I do a lot of salvaged lumber work, and even cut down some mesquite logs with a jig.  For the price I could have bought 3 blades for one Freud Blade.  If all I did was construction I’d just have a stack in my truck and put a new one in whenever one got dull.

However, this pretty good value did not stop my from just spending $73 on a Freud Industrial Full Kerf ATBR 50T Blade that arrives today.

Freud LU84R011 10-Inch 50-tooth ATB Combination Saw Blade with 5/8-Inch Arbor and PermaShield Coating

127241Will my new saw blade that cost 5 times of the HF blade be 5 times better?  I’m not sure about that.  The value probably wont be noticeable at first but I imagine better cuts, especially with heavier stock and with crosscuts on veneered plywood.  I also hope it lasts much longer.

I plan on soaking the HF blade with a dawn/vinegar solution to clean off all the pitch and resin.  Then keep it.  It will be an extra for when I send off the new blade to get sharpened, or if I’m doing some pallet project where I’m not sure if a stray nail may be present.

Other than this, I’m over my HF phase, sure I get lucky every once in a while, but I’ve now come to the point in my woodworking where I’d rather buy quality once, then something cheap twice.    That’s not always getting the absolute best on the market, I wish I had a shop full of Powermatic, Grizzly, or Festool.  Rather it’s doing my research and buying the best quality that I can reasonably afford.

God Bless,


3 thoughts on “A Year With a Harbor Freight Table Saw Blade

  1. I’ve heard stories about guys using cheap carbide tip blades in their table saws. When something goes wrong and they get binding on the table saw, one of the cheap carbide teeth dislodges from the blade and shoots into the guy’s chest like a bullet. True story. Im glad you’re using a quality blade.


    • Ouch! Another reason to always wear proper safety gear when woodworking. I’ll admit I got lucky with this cheapo blade. HF really cuts corners in QC, one time you’re fine the next, not so much.

      I’ve tried a bunch of different brand blades for all my saws over the years. Every time I’ve ponied up and bought a Freud I’ve not been disappointed. This one is the “Industrial Grade” so it should be even better.


  2. Update. I’ve noticed very smooth cuts. My saw runs quieter, which I assume is from the blade being better balanced and vibrating less. Another cool thing is it gives flat bottom cuts. Since I don’t have a dado stack this is a good substitute.


Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s